The 1/16' thick material is a premium quality variation of FKM. Note: Depending on the fuel cell type, the 24-bolt nut ring may or 2. Inspect the gasket and replace if necessary. This gasket is used for Radium fuel cell fill necks. the current fill plate from the fuel cell by disconnecting all electrical wires, fuel lines, and vent hoses from fuel cell fill plate. Machined and Anodized Aluminum Blank Plateġ8-0019 Gasket, 6-Bolt Fill Neck, 2.18' BC Fuel Cell Refueling Kits click on thumbnail to zoom Description Also in Universal Fuel Cells These refueling kits are designed specifically for the Radium Engineering FCST. This kit blocks off the filler hole on the Radium FCST units. Compatible with Radium Engineering 20-0197-V. The FCST is designed for EFI vehicles experiencing fuel pump starvation issues while using a competition fuel. Radium Fuel Cells, RA-Series MSRP: 839.95 - 1,399.95 797.95 - 1,329.95 Volume: 20-0606 R06A Radium Fuel Cell, 6 Gallon - (797. The Fuel Cell Surge Tank (FCST) is a fill plate replacement for popular fuel cells including Radium, ATL, FuelSafe, Pyrotect, Harmon, Jaz, etc. The components, materials, and seals are compatible with all fuel types (unleaded and leaded gasoline, diesel, AV gas, methanol, ethanol, E15, E85, etc.). Product Details Features Warranty Reviews (0) Fuel Cell by Radium®. For mating, a 6-bolt flange with a 2.18' PCD bolt circle (as found on the FCST) is required. Includes 20-0549-V Dry Break, 1.5in, Female, Vented as well as an aluminum housing, stainless steel hardware, and a gasket. Machined and Anodized Aluminum Fill NeckĢ0-0495-V Dry Break, 1.5in, Female, Direct Mount, Ventedĭesigned for direct mounting onto a fuel cell. They arrive polished and are rust resistant. The cage is made with 1 x 1 x 1/16 stainless steel tube and TIG welded by hand. This version is designed for use with the Ti Automotive BKS1000 (E5LM) brushless fuel pumps. This kit uses the 20-0148-V Fill Neck Cap (included) so filling is quick and simple. A weld-in cage will ease fuel cell installation by offering a pre-made, safe and secure, robust cradle. The 20-0197-V Direct Mount Fill Neck and Cap is perfect for filling directly into the fuel cell, as shown. See this blog article for more information on fuel cell filling.

Screw threads are the industry standard 1/4'-28. This bolt pattern is used on all Radium Engineering Fuel Cell Surge Tanks. These tubes have been tested at Radium Engineering.The Radium Engineering fuel cell fill kits can be used on any cell that uses a 6-bolt 2.18' (55mm) bolt circle mounting flange. NOTE: All tubes are translucent white excluding 20-0875 (above) and 20-0895 which are opaque black. These clamps provide a 360 degree seal with rolled edges to protect the tubing. Next, torque the reuseable stainless steel SAE J1508 clamps to 13.3 in-lbs.

This allows the tubing to fit snugly over the barb. RA-series fuel cells are designed and manufactured by Radium Engineering to meet top safety requirements set forth by the worldwide safety organizations FiA and SFI. Type of Fuel Only two of the pumps listed in the table above were. A competition grade fuel cell provides maximum performance and safety for high performance vehicles. This pump will operate at a very low pressure (less than 5psi) so it will draw low current and flow more than its advertised flow rate, which is usually at 3 Bar (43.5 psi). When installing, run hot water over the ends first to loosen the material. This is the pump that moves fuel from the OEM fuel tank (or fuel cell) to the surge tank. There are 2 inner diameter sizes available including 5/16' (8mm) and 3/8' (10mm). The flexible convoluted tubing is manufactured from polyamide nylon and is therefore resistant to all fuel types including alcohol blends such as E85 and suitable for EFI fuel pressure. Installation instructions available at Fuel cell surge tank for use inside competition fuel cells. These fuel tubing kits are commonly used for plumbing in-tank submerged fuel pumps.

Radiumauto fuel cell